Products / AUTOMATION AND SECURITY

BOOM BARRIER


A boom barrier is a bar, or pole pivoted to allow the boom to block vehicular access through a controlled point. Typically the tip of a boom gate rises in a vertical arc to a near vertical position. Boom gates are often counterweighted, so the pole is easily tipped. Boom gates are often paired either end to end, or offset appropriately to block traffic in both directions. Some boom gates also have a second arm, which pivots on links that allow the second arm to hang 300 to 400 mm below the upper arm when it descends into the horizontal position, to increase approach visibility.

Specification
  • Barrier operator with electronic control board.
  • Aluminum profile barrier with rubber padding.
  • Signaling light.
  • Push Button / Key operated button.
  • Safety Beam / photo switch / loop sensor.
Download Catalogue

ROAD BARRIER


We manufacture a qualitative range of Road Barriers, which are use to reducing the possibility of any difficulty on the roads. These products are manufactured using high quality raw materials using latest designs. We offer these products in varied sizes and shapes and these products are widely acknowledged for their durability as well as low maintenance. Our products are available in the market in different looks and patterns and we offer these products at market leading prices to our clients.

Road barrier for roads or passageways up to 6.5 m wide Meet EVA, the new generation of road barriers. The standout feature of this model is the control box positioned in the upper part of the barrier which can be quickly and easily programmed. Photocells can also be incorporated into all models thanks to an innovative slot-in system.

Specification
  • Resistant to heavy impacts
  • Flexible
  • Effective
  • Safe and Secure
Download Catalogue

AUTOMATIC BOLLARD


Operated either pneumatically or hydraulically, the TENTRONIX300 series offers the highest standard of anti-ramming and security protection. Taking as little as 2 seconds to reach the fully raised position, these bollards can be used in the most demanding locations where high-volume traffic flows must be managed. The TENTRONIX300 bollards are often combined with light arm barriers to provide maximum deterrence and safety. With a hard-wearing stainless steel finish, the bollards are engineered to meet the DOS and PAS standards for anti-ramming and are used extensively to protect sensitive government and military locations as well as civilian compounds. When powered by TENTRONIX's innovative pneumatic system, the bollards can be operated at very high speeds and when combined with a light arm, the air pressure can be used to simply and accurately synchronize with other elements in the system. The use of air pressure also significantly reduces the wear and tear on the components and provides years of maintenance free use.

With a patent-pending mechanism for releasing the internal piston, the bollards can be maintained without disassembly and if necessary, the entire unit can be removed without the need for digging out the foundations.
Download Catalogue

CRASH RATED CABLE BARRIERS


Designed to completely close an entrance line to a facility and bring vehicles to a rapid halt, TENTRONIX's T-Series drop arm cable barriers are the barriers of choice for military, government and commercial installations around the world.

TENTRONIX's T-Series cable barriers are constructed to provide the highest level of protection against ramming. In the event of an attempt to break through the barrier, the cables, which are hidden in the body of the gate arms, capture the chassis of the vehicle and transfer the energy of the moving vehicle to the concrete anchors. These anchors, which can be surface mounted or below surface, then wrap around the vehicle and bring it to a complete halt.

Engineered to meet both the US DOS and UK PAS standards, the unique T-Series anti-ramming design has been proven in the field against threats including terror and theft. The T-Series barriers are installed across the world and are the de-facto standards for drop arm barrier solutions for the security services and military in a number of countries. The T600 and T500 are also used extensively to protect commercial interests with the two-way barriers preventing threats from entering or exiting.
Download Catalogue

SPIKE SYSTEM


The unique and innovative T100 spike system was developed with the specific aim of bringing a vehicle to a halt without harming passengers. Designed to rip tires apart and even withstand the latest generation of run-flat tires, the T100 has been proven in the field as a particularly effective solution for border crossings and locations where vehicles pass at high speed.

Pneumatically operated and typically synchronized with a light arm barrier, the T100 system comprises a set of hollow spikes which cross the entire width of the lane. When the barrier is down, the spikes are locked in the raised position and when the barrier is raised, the spikes are lowered into the ground allowing cars to pass over safely.

The hollow spikes have been engineered to ensure that a vehicle will be disabled irrespective of the approach direction. The height and width of the spikes have been specifically designed to rip apart both small private vehicle tires and large commercial vehicle tires. Even run-flat tires which use either the solid wall or wheel band method, are similarly disabled by this system which is particularly ruthless in its ability to shred a tire and damage the wheel.Suitable for all weather conditions, the spike system incorporates a self-cleaning mechanism and drainage.

Download Catalogue

ELECTRO MECHANICAL TYRE KILLERS


Electrically operated Axel Breaker of 3/4/5/6 meters. Hydraulic/Electromechanical Drive Mechanisms consist of suitable size reversible motor, Oil Filled and sealed composite geardrive unit with internal locking feature circuit controller for Auto Off in fully raised & lowered position withlimit switches and manual Operation in case of Power failure. PCB Electronic Circuit to automatically switch off motor in case of fault.

Specification
  • Blocking Height at 60 position : 450 mm minimum
  • Spike to Spike distance : 150 mm (maximum)
  • Opening-Closing : 2 Sec
  • Steel Structure to be capable to withstand : 25/10 Ton Vehicle Load
Download Catalogue

TOLL BARRIERS


Leveraging on the rich industry experience, we have been able to provide the customers with a remarkable range of Electromechanical Boom Barriers with the highest speed.

Fabricated using genuine components, the range is electrically operated and is used at the entrances to provide an alternative to single lane use.

The range is so designed that even after the complete damage to the motor during pressure boom, the drive mechanism will not be affected in any way.

Specification
  • Mechanism: electric
  • Power Supply: 0.5 HP motor, 110-240V AC
  • Length: up to 3 meters
  • Speed: 0.9 secs
Download Catalogue

FLAP BARRIERS


Our renowned Flap Barriers entry system line utilizes the most advanced security optical sensing technology integrated into an ergonomic cabinet. Our designs focus on aesthetics and provide easy ingress/egress to any facility where installed, thereby ensuring security and controlled access. Our flap barrier solution can blend seamlessly into any lobby or prominent entryway.

TENTRONIX's Flap Barriers are user-friendly solutions that facilitate "Self Service" bi-directional entry control into secure areas at high throughput capacities. The motorized barriers are equipped with sliding or swinging barrier panels controlled by our advanced microprocessor platform running our highly tuned detection software algorithm. We selected the best available IR beam technology for our sensor arrays and engineered the detection system to be easily tuned "on site" by selecting a choice of safety & security settings best suited for the specific environment and desired security levels.

Application Areas: Office Buildings, Corporate Lobbies, Governmental Facilities, Financial Institutions, Defense Installations, Data Centers, University/Educational Institutions, Leisure Centers and Bus Terminals/Depots.

Specification
  • High performance secure entry solution
  • Fast throughput rates
  • User-friendly operation with safety redundancy
  • Ease of peripherals integration
  • Numerous finish options available
Download Catalogue

HYDRAULIC RISING ROAD BLOCKERS


Road blockers are designed especially for entrance points which have a threat of vehicle attack or for the ones that have high security requirements. If there is a threat of vehicle attack in addition to the control of vehicle access in high security applications, hydraulic road blockers are the unique solution and the most secure systems. Even though the attack is from high tonnage vehicles with high speeds, it's not possible for the vehicle to keep on moving because of the damage given to front, wheels and the bottom of the vehicle. Optima road blockers are designed to K12 standards. Finite element model analyses are available upon request. Drive unit is electro-hydraulic, but in case of power failure road blocker can be lowered or lifted manually with the help of hand pump. Typical raise/lower time is 3 seconds. In case of emergency, raise/lower time can be as low as 1.5 seconds. With the help of PLC (programmable logic control), raise/lower function can be achieved by every kind of card readers, biometric readers like fingerprint or hand shape, radio control, on/off key switch etc. Besides, safety accessories like photocells, inductive loop detectors, flashing lights or red/green traffic lights can be integrated to the system very easily. Typical weight of a road blocker is 2-2.5 tons (depending on road blocker type).

Download Catalogue